1. Common Faucet Problems & Causes
Most faucet troubles trace to a small set of internal components — and most are economical repairs.
A faucet's function depends on a few key parts: the cartridge or stem (which controls flow and, in single-handle faucets, temperature), O-rings and seals, the aerator (which shapes the stream), and the supply lines feeding it. When one fails, the symptom is usually a drip, a leak, or a flow change.
Identifying which component has failed is the diagnostic step; the repair itself is typically quick.
- Drip from the spout: worn cartridge, stem, or washer no longer sealing.
- Leak at the handle base: hardened O-rings or a loose packing nut.
- Leak under the sink: failed supply line or corroded shutoff valve.
- Reduced flow: clogged aerator or blocked supply line.
- Hard to turn / stiff handle: mineral scale in the cartridge.
2. Cartridge Repair vs. Faucet Replacement
The decision hinges on the faucet's overall condition and parts availability.
If the faucet body is sound and the finish is good, replacing a worn cartridge or set of O-rings is usually the economical choice — it resolves the leak and extends the faucet's life for a fraction of replacement cost.
Replacement becomes the smarter call when the finish is badly corroded, internal parts are discontinued (common with older or imported brands), the body is cracked, or the faucet is old enough that another failure is likely soon. We advise honestly based on what we find.
3. Aerators, Flow & Low Pressure
Not every flow problem is a pressure problem — often it's a simple aerator issue.
The aerator is the small screen at the spout tip. It shapes the stream and conserves water, but it also catches sediment and mineral scale — and when it clogs, flow drops at that single faucet.
A clogged aerator is one of the most common and easily resolved faucet issues. Cleaning or replacing it often restores full flow in minutes. If low flow persists at every fixture, that points to a system-wide cause we'd diagnose separately.
4. Supply Lines & Shutoff Valves
The components under the sink matter as much as the faucet above it.
The shutoff valves (the small handles on the wall under the sink) and the braided supply lines connecting them to the faucet are common sources of slow, hidden leaks. Corroded valves and aged supply lines can seep for months before being noticed, damaging the cabinet floor.
On every installation we inspect these components and replace supply lines as part of the job. A new faucet on old, corroded supply lines is a leak waiting to happen.
Check Under the Sink Periodically
Most under-sink leaks run silently. A quick check of the cabinet base for moisture every few months catches supply-line and valve leaks before they damage the cabinetry.
5. New Faucet Installation Considerations
A proper faucet installation involves more than the fixture itself.
Beyond setting the new faucet, a complete installation includes inspecting and replacing the supply lines, verifying the shutoff valves work (a stuck valve is a flood risk), checking the drain assembly and pop-up stopper, and confirming proper flow and temperature mixing.
These are the steps that separate a lasting installation from one that leaks within a year. We handle them on every job — not as add-ons.
6. When to Call a Plumber
Some faucet issues are DIY-friendly; others benefit from professional service.
An aerator cleaning or a visible, accessible cartridge swap may be a DIY candidate for a handy homeowner with the right tools. But corroded shutoff valves, stuck cartridges, supply-line replacements, and any new installation all warrant professional service — these are where DIY attempts most often cause bigger leaks.
Faucet Service Options
Component repair for sound fixtures, full replacement when it's the smarter call.
Cartridge / Stem / Aerator Repair
Targeted replacement of the failed internal component — a worn cartridge, hardened O-rings, or a clogged aerator — restoring proper sealing and flow without replacing the whole faucet.
When recommended: Ideal when the faucet body and finish are sound and the leak or flow issue is isolated to a serviceable internal part.
Check Repair PricingNew Faucet Installation
Full removal of the old faucet, shutoff valve and supply line inspection, and installation of a new fixture — including customer-supplied or Plumbing SFL-sourced faucets.
When recommended: Best when the faucet is corroded, parts are discontinued, or you're upgrading finishes or functionality during a refresh.
Check Installation PricingThe Plumbing SFL Fixture Standard
Component-level diagnosis, clean installation, no surprise add-ons.
Upfront Flat-Rate Pricing
You review the exact price for the repair or installation before any work begins.
Valve & Supply Line Inspection
On every install we inspect the shutoff valves and supply lines — the hidden cause of slow leaks under the sink.
Aerator & Flow Check
We verify proper flow and check the aerator so a new faucet performs as expected from day one.
Toilet Repair & Installation
Toilet component repair and new fixture installation.
Core ServiceShower & Tub Plumbing
Shower valve, tub spout, and showerhead repair and replacement.
Core ServiceWater Pressure / Pressure Regulator Services
Whole-house pressure testing when low flow isn't isolated to one faucet.
Core ServiceGarbage Disposal Repair & Installation
Kitchen sink disposal repair and replacement.
Save on Service & Diagnostics
VIP members pay no service call fee and get 10% off all work. $299 a year, no auto-renew.
View VIP BenefitsFlexible Payment Options
Financing available through Wisetack, Klarna and PayPal Pay Later.
How Pricing Works